iwan.hoogendoorn
NSX · · 10 min read

Configure NSX-T Logical Bridging (single profile)

In this wiki article, I will show you how to configure Layer 2 Bridging between a VLAN (on the physical network) and a Segment (overlay network) on NSX-T with the same subnet. The goal is to not route network traffic through the Tier-0 and Tier-1 Gateways but to bridge network traffic using Layer 2 Logical bridging.

The Network Diagram

Chapter 09-Bridging Components with IPs

The goal of this article is to show you that the 172.16.30.12 IP address on VLAN 300 will be able to communicate with the 172.16.30.10 IP address on the NSX-T overlay using a Layer 2 Logical Bridge.

The high-level steps

In this wiki article, the high level following steps will be discussed:

  • STEP 1: Create vDS Bridge Port-Group (TRUNK)
  • STEP 2: Create a new NSX-T Transport Zone (dedicated for the bridge interface)
  • STEP 3: Add the new Transport Zone (Bridge) to the existing Edge Transport Nodes
  • STEP 4: Create a Bridge Profile
  • STEP 5: Configure a VLAN on the physical network with a gateway IP address
  • STEP 6: Create test Virtual Machines on this VLAN to perform some ping tests
  • STEP 7: Configure a Segment as an overlay network (on NSX-T) with a gateway IP address by attaching it to a Tier-1 Gateway
  • STEP 8: Create test Virtual Machines on this Segment to perform some ping tests
  • STEP 9: Configure the overlay network (Segment) as a Layer 2 Bridge-Backed Segment
  • STEP 10: Perform some ping and traceroute tests between the VLAN and NSX-T Segment Virtual Machines
  • STEP 11: Perform traceflow tests between the VLAN and NSX-T Segment Virtual Machines
  • STEP 12: Looking at the bridge statistics

The configuration steps

STEP 1» Create vDS Bridge Port–Group 〈TRUNK〉

First, we need to create a VDS port group (on vSphere) that we will use for the Edge transport Node so that it can map one of the fast-path interfaces to this port group.

Go to the VDS and create a new port group.

CREATE-BRIDGE-PG-1

Give it a name. In my case, I named it “BRIDGE-TRUNK”.

CREATE-BRIDGE-PG-2

Make the VLAN Type a “VLAN Trunk” and allow all VLANs here. It is important that all the VLANs that you want to bridge are in this range.

CREATE-BRIDGE-PG-3

Make sure that all thee port group security settings are set to “Accept”.

CREATE-BRIDGE-PG-4

Do not change anything here.

CREATE-BRIDGE-PG-5

Now move the second uplink to the “standby uplinks” section and leave the first uplink in the “active uplinks” section.

CREATE-BRIDGE-PG-6

Do not change anything here.

CREATE-BRIDGE-PG-7

Do not change anything here.

CREATE-BRIDGE-PG-8

Verify all your configuration settings and add the new port group.

CREATE-BRIDGE-PG-9

STEP 2» Create a new NSX–T Transport Zone 〈dedicated for the bridge interface〉

Add a new Transport Zone dedicated to bridging.

NSX-T GUI: System >> Configuration >> Fabric >> Transport Zones >> +Add

Add a new VLAN Transport Zone.

CREATE-BRIDGE-TZ-1

Verify if the new Transport Zone is added.

CREATE-BRIDGE-TZ-2

STEP 3» Add the new Transport Zone 〈Bridge〉 to the existing Edge Transport Nodes

We now need to add an additional NVDS with that Transport Zone to the existing Edge Transport Nodes.

This is a list of my existing Edge Transport Nodes. Pay attention to the number of NVDSs (this is now 1)

ADD-TZ-TO-EDGE-1

Let’s add the new NVDS and transport zone to the first Edge transport Node.

ADD-TZ-TO-EDGE-2

Let’s add the new NVDS and transport zone to the second Edge transport Node.

ADD-TZ-TO-EDGE-3

Verify if the number of NVDSs has increased to 2.

ADD-TZ-TO-EDGE-4

STEP 4» Create a Bridge Profile

Now create a Bridge Profile.

NSX-T GUI: Networking >> Connectivity >> Segments >> Edge Bridge Profiles >> Add Edge Bridge Profile

ADD-BRIDGE-PROFILE

STEP 5» Configure a VLAN on the physical network with a gateway IP address

I have used a virtual Vyatta Router that I have configured for networking. The configuration for the interfaces for Bridging is below.

Terminal window
configure
set interfaces ethernet eth1 vif 300 address '172.16.30.1/24'
set interfaces ethernet eth1 vif 300 description 'Bridge Test VLAN 300'
set interfaces ethernet eth1 vif 300 mtu '1500'
commit
save
Terminal window
vyos@Pod-120-Router:~$ show interfaces
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
---- ---------- --- -----------
<...>
eth1 - u/u
eth1.300 172.16.30.1/24 u/u Bridge Test VLAN 300
<...>
vyos@Pod-120-Router:~$

STEP 6» Create test Virtual Machines on this VLAN to perform some ping tests

Create VLAN 300 Port Group

Now, we need to create a VDS port group (on vSphere) to simulate the “external” VLAN 300.

Go to the VDS and create a new port group.

CREATE-VLAN-PG-1

Give it a name. In my case, I named it “Pod-120-VDS-VLAN300”.

VLAN300-1

Make the VLAN Type a “VLAN” and type in VLAN 300 here.

VLAN300-4

Verify all your configuration settings and add the new port group.

VLAN300-5

Verify if the VLAN port group with VLAN 300 is added

VLAN300-6

Create a Photon OS VM

Deploy a new OVF Template from the Center Server Client.

DEPLOY-VLAN-VM-1

Select the local Photon OS ova file.

DEPLOY-VLAN-VM-2

Provide a name for your Virtual Machine.

DEPLOY-VLAN-VM-3

Select a computing resource where you want to deploy the VM to.

DEPLOY-VLAN-VM-4

Review the details and just click next.

DEPLOY-VLAN-VM-5

Accept the license agreement.

DEPLOY-VLAN-VM-6

Select a storage resource where you want to deploy the VM to.

DEPLOY-VLAN-VM-7

Select a networking resource that you want you’re VM to be attached to. Make sure you select the VLAN 300 port group you created. Review the details before you finish (screenshot not shown).

DEPLOY-VLAN-VM-8

Power on the new Virtual Machine.

DEPLOY-VLAN-VM-9

Network Configuration and Ping Tests

When the VM is ready and power on we need to log in to the console and provide network settings. the first time you log in to a newly deployed Photon OS VM you need to change the password. The default username is “root” and the default password is “changeme”.

Terminal window
Welcome to Photon 3.0 (x86_64) - Kernel 4.19.79-1.ph3-esx (tty1)
photon-machine login: root
Password: changeme
You are required to change your password immediately (administrator enforced)
Changing password for root.
Current password: changeme
New password: VMware1!VMware1!
Retype new password: VMware1!VMware1!

Here we change the hostname.

Terminal window
root@photon-machine [ ~ ]# hostnamectl set-hostname l2b-vm-vlan

Here we create a network interface configuration file to specify the static IP address details for the network interface.

Terminal window
root@photon-machine [ ~ ]# vi /etc/systemd/network/10-static-en.network

This is the content of the “10-static-en.network” file.

Terminal window
[Match]
Name=eth0
[Network]
Address=172.16.30.12/24
Gateway=172.16.30.1

Here we change the rights to the file so the system is allowed to use it.

Terminal window
root@photon-machine [ ~ ]# chmod 644 /etc/systemd/network/10-static-en.network

Here we restart the networking service of the VM.

Terminal window
root@photon-machine [ ~ ]# systemctl restart systemd-networkd

Here we reboot the machine.

Terminal window
root@photon-machine [ ~ ]# reboot

When the machine is rebooted (with the new hostname) we can verify if the IP address is correct.

Terminal window
root@l2b-vm-vlan [ ~ ]# ip a

PING-30-1

Here I do a quick ping towards my gateway to verify if we have network connectivity.

PING-30-2

STEP 7» Configure a Segment as an overlay network 〈on NSX–T〉 with a gateway IP address by attaching it to a Tier–1 Gateway

Now we need to create a NSX-T Overlay segment that we are going to use to bridge VLAN 300 with.

NSX-T Manager GUI: Networking >> Connectivity >> Segments >> Add Segment

SEG-BRIDGE-1

Verify if the Segment is correctly added.

SEG-BRIDGE-2

STEP 8» Create test Virtual Machines on this Segment to perform some ping tests

Deploy a new OVF Template from the Center Server Client.

DEPLOY-BRIDGE-VM-1

Select the local Photon OS ova file.

DEPLOY-BRIDGE-VM-2

Provide a name for your Virtual Machine.

DEPLOY-BRIDGE-VM-3

Select a computing resource where you want to deploy the VM to.

DEPLOY-BRIDGE-VM-4

Review the details and just click next.

DEPLOY-BRIDGE-VM-5

Accept the license agreement.

DEPLOY-BRIDGE-VM-6

Select a storage resource where you want to deploy the VM to.

DEPLOY-BRIDGE-VM-7

Select a networking resource that you want you’re VM to be attached to. Make sure you select the NSX-T (Bridge) overlay Segment you created.

DEPLOY-BRIDGE-VM-8

Review the details before you finish.

DEPLOY-BRIDGE-VM-9

Power on the new Virtual Machine.

DEPLOY-BRIDGE-VM-10

Network Configuration and Ping Tests

When the VM is ready and power on we need to log in to the console and provide network settings. the first time you log in to a newly deployed Photon OS VM you need to change the password. The default username is “root” and the default password is “changeme”.

Terminal window
Welcome to Photon 3.0 (x86_64) - Kernel 4.19.79-1.ph3-esx (tty1)
photon-machine login: root
Password: changeme
You are required to change your password immediately (administrator enforced)
Changing password for root.
Current password: changeme
New password: VMware1!VMware1!
Retype new password: VMware1!VMware1!

Here we change the hostname.

Terminal window
root@photon-machine [ ~ ]# hostnamectl set-hostname l2b-test-vm-nsx

Here we create a network interface configuration file to specify the static IP address details for the network interface.

Terminal window
root@photon-machine [ ~ ]# vi /etc/systemd/network/10-static-en.network

This is the content of the “10-static-en.network” file.

Terminal window
[Match]
Name=eth0
[Network]
Address=172.16.30.10/24
Gateway=172.16.30.1

Here we change the rights to the file so the system is allowed to use it.

Terminal window
root@photon-machine [ ~ ]# chmod 644 /etc/systemd/network/10-static-en.network

Here we restart the networking service of the VM.

Terminal window
root@photon-machine [ ~ ]# systemctl restart systemd-networkd

Here we reboot the machine.

Terminal window
root@photon-machine [ ~ ]# reboot

When the machine is rebooted (with the new hostname) we can verify if the IP address is correct.

Terminal window
root@l2b-test-vm-nsx [ ~ ]# ip a

STEP 9» Configure the overlay network 〈Segment〉 as a Layer 2 Bridge–Backed Segment

Now I need to enable the bridging between the NSX-T overlay Segment and the VLAN. I do this inside the actual overlay segment we want to use for bridging.

NSX-T GUI: NSX-T Manager GUI: Networking >> Connectivity >> Segments >> SEG-BRIDGE >> EDIT

There is a label there called “Edge Bridges” click on “Set”

BIND-BRIDGE-1

Select the Edge Bridge Profile and the Transport Zone that you created earlier. I have also added the VLAN 300 that I want to bridge to.

BIND-BRIDGE-2

Verify if the Edge Bridge is added.

BIND-BRIDGE-3

Verify if you see a little “1” in the Segment settings.

BIND-BRIDGE-4

STEP 10» Perform some ping and traceroute tests between the VLAN and NSX–T Segment Virtual Machines

Because I am using Photon OS I first need to open up some INBOUND IPTABLE rules on the Tenant Virtual Machines to allow ping and traceroute/tracepath.

Open ICMP and UDP to allow ping and tracepath tests on the VLAN VM

IPTAB-2

Open ICMP and UDP to allow ping and tracepath tests on the OVERLAY VM

IPTAB-1

Tests from the VLAN VM to the OVERLAY VM

In the test below you can see that ping is working and that the tracepath is only showing one hop.

PINGTEST-01

Tests from the OVERLAY VM to the VLAN VM

For the other way around you can see (below) that ping is working and that the tracepath is also only showing one hop.

PINGTEST-02

STEP 11» Perform traceflow tests between the VLAN and NSX–T Segment Virtual Machines

I also tried to use traceflow to see if I could retrieve some information from there.

TF-01

But unfortunately, traceflow does not support bridged traffic flow tests.

TF-02

STEP 12» Looking at the bridge statistics

There is also a way to look at the bridge statistics under the segment.

Click on “view statistics”.

SEG-STATS-1

Look at the statistics.

SEG-STATS-2

I am always trying to improve the quality of my articles so if you see any errors, mistakes in this article or you have suggestions for improvement, please contact me and I will fix this.

Originally published on the old wiki at /index.php/Configure_NSX-T_Logical_Bridging_(single_profile).