iwan.hoogendoorn
Networking · · 5 min read

Networking With Raspberry Pi 2

I created a shoppinglist and order the Raspberry Pi components (below)

RPI Hosts

rpi2-1 = B8:27:EB:CD:CF:E4

rpi2-2 = B8:27:EB:7E:C7:AC

The Mac address information is correct according IEEE ouisearch

Software

Install Ubuntu for the Raspberry Pi 2

  1. Build the RPI2 into the SOS Behuizing Regenboog
    1. The case is build out of small plates that are numbered, the numbers indicate the order of the plates where the RPI2 falls in.
    2. The most top and most bottom plates are blank
  2. Formatted the SD card with SD Formatter
  3. Created OS image for RPI2
    1. Ubuntu MATE
      1. Downloaded Win32 Disk Imager
      2. Downloaded Ubuntu MATE
      3. Wrote the image to the microSD card
    2. Ubuntu 14.04 LTS
      1. Downloaded + created image Ubuntu 14.04 LTS
  4. Booted up the RPI2 and did the pre-install steps needed for:
    1. Ubuntu MATE
    2. Ubuntu 14.04 LTS

Enable SSH

iwan@rpi2-1:~$ ##b####y##sudo apt-get install openssh-server

iwan@rpi2-2:~$ ##b####y##sudo apt-get install openssh-server

Now I am able to log in with SSH.

Install Iperf

iwan@rpi2-1:~$ ##b####y##sudo apt-get install iperf

iwan@rpi2-2:~$ ##b####y##sudo apt-get install iperf

Install Tshark and Wireshark

iwan@rpi2-1:~$ ##b####y##sudo apt-get install tshark wireshark

iwan@rpi2-2:~$ ##b####y##sudo apt-get install tshark wireshark

Iperf

Check IP addresses

Terminal window
iwan@rpi2-1:~$ ifconfig
eth0 Link encap:Ethernet HWaddr b8:27:eb:cd:cf:e4
inet addr:10.11.11.175 Bcast:10.11.11.255 Mask:255.255.255.0
inet6 addr: fe80::ba27:ebff:fecd:cfe4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3794 errors:0 dropped:0 overruns:0 frame:0
TX packets:696 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1343222 (1.3 MB) TX bytes:86769 (86.7 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:362 errors:0 dropped:0 overruns:0 frame:0
TX packets:362 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:34861 (34.8 KB) TX bytes:34861 (34.8 KB)
iwan@rpi2-1:~$
Terminal window
iwan@rpi2-2:~$ ifconfig
eth0 Link encap:Ethernet HWaddr b8:27:eb:7e:c7:ac
inet addr:10.11.11.171 Bcast:10.11.11.255 Mask:255.255.255.0
inet6 addr: fe80::ba27:ebff:fe7e:c7ac/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8185 errors:0 dropped:0 overruns:0 frame:0
TX packets:2738 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5417894 (5.4 MB) TX bytes:450477 (450.4 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:633 errors:0 dropped:0 overruns:0 frame:0
TX packets:633 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:72151 (72.1 KB) TX bytes:72151 (72.1 KB)
iwan@rpi2-2:~$
Hostname Role IP Address
rpi2-1 SERVER 10.11.11.175
rpi2-2 CLIENT 10.11.11.171

Test 1

Start the iperf server service on rpi2-1.

Terminal window
iwan@rpi2-1:~$ iperf -s
----
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
----

Start the iperf client service on rpi2-2.

Terminal window
iwan@rpi2-2:~$ iperf -c 10.11.11.175
----
Client connecting to 10.11.11.175, TCP port 5001
TCP window size: 43.8 KByte (default)
----
[ 3] local 10.11.11.171 port 53385 connected with 10.11.11.175 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 113 MBytes 94.4 Mbits/sec
iwan@rpi2-2:~$

View results on the server.

Terminal window
iwan@rpi2-1:~$ iperf -s
----
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
----
[ 4] local 10.11.11.175 port 5001 connected with 10.11.11.171 port 53385
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 113 MBytes 94.1 Mbits/sec

Test 2

Start the iperf server service on rpi2-1.

Terminal window
iwan@rpi2-1:~$ iperf -s
----
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
----

Start the iperf client service on rpi2-2.

Terminal window
iwan@rpi2-2:~$ iperf -c 10.11.11.175 -r
----
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
----
----
Client connecting to 10.11.11.175, TCP port 5001
TCP window size: 70.0 KByte (default)
----
[ 5] local 10.11.11.171 port 53386 connected with 10.11.11.175 port 5001
[ ID] Interval Transfer Bandwidth
[ 5] 0.0-10.0 sec 112 MBytes 93.6 Mbits/sec
[ 4] local 10.11.11.171 port 5001 connected with 10.11.11.175 port 40047
[ 4] 0.0-10.1 sec 113 MBytes 94.1 Mbits/sec
iwan@rpi2-2:~$

View results on the server.

Terminal window
iwan@rpi2-1:~$ iperf -s
----
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
----
[ 4] local 10.11.11.175 port 5001 connected with 10.11.11.171 port 53386
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.1 sec 112 MBytes 93.2 Mbits/sec
----
Client connecting to 10.11.11.171, TCP port 5001
TCP window size: 70.0 KByte (default)
----
[ 4] local 10.11.11.175 port 40047 connected with 10.11.11.171 port 5001
[ 4] 0.0-10.0 sec 113 MBytes 94.4 Mbits/sec

Conclusion

At first I was wondering why I did not got more troughput then 1 Gb/sec, but then I discovered that the RPi2 only has a FastEthernet interface, and I tought it had a GigabitEthernet interface:

Terminal window
iwan@rpi2-1:~$ dmesg|grep eth0
[ 2.356975] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:cd:cf:e4
[ 30.472266] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 32.084114] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
iwan@rpi2-1:~$
Terminal window
iwan@rpi2-2:~$ dmesg|grep eth0
[ 2.340162] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:7e:c7:ac
[ 29.505781] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 31.131441] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
iwan@rpi2-2:~$

Tshark and Wireshark

Cisco Switch Config

Device Switchport Role
Source box Gi0/22 SOURCE
Wireshark box Gi0/23 DESTINATION
Terminal window
!
interface GigabitEthernet0/22
description Source box
switchport access vlan 11
switchport mode access
spanning-tree portfast
no shut
!
default interface GigabitEthernet0/23
!
monitor session 1 source interface gigabitEthernet 0/22 both
!
monitor session 1 destination interface gigabitEthernet 0/23 encapsulation replicate
!

Wireshark Capture

Terminal window
iwan@rpi2-1:~$ sudo tshark -f "port 80" -i eth0 -w /tmp/capture-18-06-15-1542.cap
[sudo] password for iwan:
tshark: Lua: Error during loading:
[string "/usr/share/wireshark/init.lua"]:46: dofile has been disabled due to running Wireshark as superuser.
See http://wiki.wireshark.org/CaptureSetup/CapturePrivileges for help in running Wireshark as an unprivileged user.
Running as user "root" and group "root". This could be dangerous.
Capturing on 'eth0'
1027
Ctrl-C

The capture was aborted with the “Ctrl-C” input.

View if the results are available:

Terminal window
iwan@rpi2-1:/$ cd tmp/
iwan@rpi2-1:/tmp$ ls -l
total 876
-rw------- 1 root root 894976 Jun 18 15:46 capture-18-06-15-1542.cap
iwan@rpi2-1:/tmp$

Originally published on the old wiki at /index.php/Networking_With_Raspberry_Pi_2.